Just How to Replace a Bathtub in Your Bathroom
Just How to Replace a Bathtub in Your Bathroom
Blog Article
The article down below involving A Step-by-Step Guide to Installing a Bathtub is rather stimulating. You should take a look.
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably hard job. If the old tub is conveniently obtainable, the job can move speedily; if you need to open a wall surface to get rid of the old tub and place the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the task and fit attempting it. Rather than working with a professional to take control of a halfway-completed job, it is better to take into consideration employing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This article will certainly help you mount a new bathtub in your shower room if you have actually currently bought a brand-new tub and also don't require to change the setup of your previous supply of water pipes.
Your tools and product checklist should consist of the following:
Planning for the Setup
First of all, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, then the first thing you must do is detach the water. After doing so, activate the taps to drain any water remaining in the system. The procedure of eliminating the existing faucets can be rather troublesome as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wood boards under its feet, position the tub in the needed position. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small factors.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bathtub till the level checks out level.
To install taps, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Activate the supply of water and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise examine the overflow electrical outlet and the regular outlet for leaks.
Finally, deal with the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait till the tub has been made use of at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Protect the tap in place with the manufacturer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The previous type needs to be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in problems with moisture and also feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes as well as cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can split relatively very early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that article about How to Install a Bathtub through an acquaintance on a different web page. Do you know another individual who is occupied with the subject? Please feel free to share it. I praise you for your time. Visit again soon.
This Resource Report this page